anyone have dimensions of Princeton reverb chassis ?

pula58 · Post by **pula58** » Tue Apr 10, 2012 4:05 pm

I am looking for a good mechanical drawing of a Fender princeton reverb chassis. One that would show major cutout openings (like Power tranny, capacitor can, etc)

thanks!

P.

M Fowler · Post by **M Fowler** » Tue Apr 10, 2012 6:48 pm

I haven't seen info for a real Princeton chassis only Weber's which is not precise.

rdjones · Post by **rdjones** » Tue Apr 10, 2012 7:24 pm

M Fowler wrote:I haven't seen info for a real Princeton chassis only Weber's which is not precise.

The angle on the front panel is different.
The original is 15°, (75° as shown on the drawing) isn't it ?

rd

Deric · Post by **Deric** » Tue Apr 10, 2012 8:17 pm

Here's one for the Mojo chassis....I believe it's pretty close.

pula58 · Post by **pula58** » Wed Apr 11, 2012 2:15 am

[quote="Deric"]Here's one for the Mojo chassis....I believe it's pretty close.[/quote

Thank you very much, I really appreciate you sharing this!

P.

pula58 · Post by **pula58** » Thu Apr 19, 2012 4:13 am

do you guys think the angle of the front is 15 or 16 degrees?

Firestorm · Post by **Firestorm** » Thu Apr 19, 2012 6:21 am

Slightly off topic: how many different angles did Fender use? Two Twins and a Bassman I have open at the moment are all 25 degrees. Smaller amps are "flatter?"

M Fowler · Post by **M Fowler** » Thu Apr 19, 2012 2:27 pm

The PR chassis data states 16 degrees angle.

pula58 · Post by **pula58** » Thu Apr 19, 2012 9:11 pm

M Fowler wrote:The PR chassis data states 16 degrees angle.

Where can you access this data?

Thanks!

P.

M Fowler · Post by **M Fowler** » Fri Apr 20, 2012 3:24 am

pula58 wrote:
M Fowler wrote:The PR chassis data states 16 degrees angle.
Where can you access this data?

Thanks!

P.

On the left hand side of the pdf post above.

Mark

pula58 · Post by **pula58** » Fri Jun 01, 2012 6:17 pm

I today measured a Silverface Bassman chassis: 25 degree faceplate angle

Today I also measured a Mojo princeton reverb replica chassis: 24.5 degrees. Probably actually is 25 degress with some measurement error.

Seems like 25 degrees it is!

vintagedream · Post by **vintagedream** » Thu Jun 07, 2012 9:29 pm

I have been producing Princeton, Bassman, Tremolux etc. chassis for 3 years now and I have found 25 degrees works for my customers.

M Fowler · Post by **M Fowler** » Fri Jun 08, 2012 2:15 am

vintagedream wrote:I have been producing Princeton, Bassman, Tremolux etc. chassis for 3 years now and I have found 25 degrees works for my customers.

In this thread is photos of the custom Tremolux chassis I had Vintagedream build for me. Great chassis.

https://tubeamparchive.com/viewtopic.ph ... c&start=30

Mark

Tube Amp Archive

anyone have dimensions of Princeton reverb chassis ?

anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Re: anyone have dimensions of Princeton reverb chassis ?

Fender chassis angle

Re: Fender chassis angle