Fender Princeton Reverb eyelet board

YouTube · Post by **xtian** » Mon Feb 10, 2014 4:49 pm

Anyone have a to-scale eyelet board drill pattern for the AA1164?

mhartman · Post by **mhartman** » Mon Feb 10, 2014 4:57 pm

xtian wrote:Anyone have a to-scale eyelet board drill pattern for the AA1164?

I don't, but you could probably use your computer to bring this one into scale (if you know the real board's dimensions). It would probably get you close:

[img

1805]https://taweber.powweb.com/store/6a14_layout.jpg[/img]

YouTube · Post by **xtian** » Mon Feb 10, 2014 7:11 pm

Sure, I can use that...but someone must have a nice plan, right? ....

YouTube · Post by **xtian** » Mon Feb 10, 2014 7:46 pm

OK! EL34world was tough to connect to today, but eventually I retrieved Hoffman's very nice artwork, attached.

drew · Post by **drew** » Mon Feb 10, 2014 8:31 pm

^ FYI, that's the version that guys in Hoffman's forum came up with. Hoffman himself later changed it up somewhat - the official Hoffman layout is here: http://www.el34world.com/Hoffman/images ... Layout.gif

YouTube · Post by **xtian** » Mon Feb 10, 2014 10:24 pm

Thx, Drew.

ToneMerc · Post by **ToneMerc** » Mon Feb 10, 2014 11:04 pm

If you have Visio, I have PR eyelet board that I drew up awhile back that's 2.625 x 10.5. However, it's spaced for the smaller body NTE caps, resistors and setup for standoffs, so if you are looking for something dead nuts comparable to Watts Audio it might not be to your liking. Then again, the core is there so you can tweak to taste.

TM

YouTube · Post by **xtian** » Mon Feb 10, 2014 11:16 pm

Thanks, but I'm going with Hoffman's layout.

beasleybodyshop · Post by **beasleybodyshop** » Tue Feb 11, 2014 2:10 am

xtian wrote:Thanks, but I'm going with Hoffman's layout.

I went with the exact same one, Xtian:

Also, I finished making my faceplate/backplate today. I made mine out of plexiglass...it looks different but I think its cool.

telentubes · Post by **telentubes** » Tue Feb 11, 2014 2:18 am

I have one of the Weber boards, populated, which you could copy.

YouTube · Post by **xtian** » Tue Feb 11, 2014 2:19 am

Really great, Beas! But watch out, your plate resistors could easily short against your ground buss. Better insulate those!

beasleybodyshop · Post by **beasleybodyshop** » Tue Feb 11, 2014 2:29 am

xtian wrote:Really great, Beas! But watch out, your plate resistors could easily short against your ground buss. Better insulate those!

Yep.....

I ended up using the original hoffman layout - After looking into more, I noticed that the official hoffman layout was better. Oh well, im already into it at this point!

Good luck with your build.

I3enjam1n · Post by **I3enjam1n** » Sat Feb 15, 2014 5:42 pm

http://www.brieskorn.de/int/Guitar___Am ... a1164.html

I made mine with these plans.

YouTube · Post by **xtian** » Sat Feb 15, 2014 6:43 pm

Wow! Welcome, and thanks for that! Beautiful artwork.

cbass · Post by **cbass** » Sun Feb 16, 2014 11:49 am

Dig them faceplates. Vury nice.

Tube Amp Archive

Fender Princeton Reverb eyelet board

Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board

Re: Fender Princeton Reverb eyelet board